Clients ask for delicate tulip accents and we lose time remaking pieces when bubbles or sink marks appear. The Size Tulips heart-shaped silicone mold has clear raised relief and a frosted body—those glossy details show every air pocket. We keep this short and technical so you can produce consistent, embossed tulip charms without wasting sets.
Station Setup: control, not chaos
Start with a clean, level surface and a chilled tray if you batch cast. Place the translucent pale lavender silicone mold flat on matte backing or a nonstick mat so the scalloped edge sits evenly. Use a single syringe or pipette for dosing; inconsistent droplet height and speed trap air. We recommend one tech per lamp when casting multiple colors to avoid interruptions that cause temperature swings.

Heart-shaped Size Tulips mold flat on dark background
Material prep: thin, degas, and suit the cavity
Solid gel that is too viscous will hold air in fine tulip petals and leaf veins. We thin only with manufacturer-approved reducers or a tiny amount of compatible monomer equivalent; never add solvents that the gel label forbids. For pigments and glitter, pre-mix slowly and let any entrained air settle for a minute before dosing. When we can, we use a mini vacuum chamber or short spin in a microcentrifuge to remove bubbles from highly filled mixes.

Glossy raised tulip relief and scalloped edge visible
Filling technique: slow pour and cavity venting
We fill the tulip cavities from the deepest point upward. Aim the syringe tip at the lowest interior corner and fill slowly until the cavity barely pools. The clear glossy raised details on this mold show thin lines where bubbles lodge, so we stop before overfilling. For tiny petal recesses use a dotting tool to coax trapped air out toward the open edge while still uncured.
Pro tip: Hold the syringe tip inside the cavity during the final micro-drop. A 45° slow release gives a continuous stream and displaces air instead of splattering it.
Curing and micro-vibration: staged and supported
We avoid a single full-power cure. For the Size Tulips mold we do a short tack cure (10–20 seconds) to stabilize the surface, then inspect under lamp light for micro-bubbles showing as tiny bright dots against the glossy relief. If present, use a single short purge pass with a micro-vibe (1–3 seconds) to encourage bubbles to rise to the surface, then finish with a longer cure (30–60 seconds) adjusted to the gel spec. Keep lamp distance consistent and avoid local overheating near raised edges which can create sink marks as material retracts.
Demold and finish: flex, don’t pull
The mold’s soft premium silicone and thin body let us flex from the scalloped edge inward. We never pull a cured petal directly; flex the mold and let the charm pop free with tweezers. If a sink mark appears along an edge, lightly refill with a thin clear gel and spot-cure for 10–20 seconds to level the rim before a final full cure.
Tools and small workflow habits that save time
- Use a low-dead-volume syringe for precise micro-dosing.
- Keep a micro-vibe and a mini vacuum available at the station for quick corrective steps.
- Label cavities on a practice strip to know which size you used so you can match dosing volumes next batch.
Pro tip: When casting color-shaded tulips, cure monochrome base layers first in short stages; layering reduces trapped air and prevents sink marks in the glossy raised veins.
Mold care and storage
Clean the mold before each use with alcohol or adhesive tape and let it dry. Store flat and out of direct sunlight so the translucent body keeps its flexibility; distortion increases bubble risk. Avoid sharp tools on the edges; thin molds tear if a cavity is forced open.
Safety and handling notes
Wear nitrile gloves when handling uncured gel and solvents. Keep a well-ventilated area for vapors and follow curing equipment guidelines. Avoid prolonged skin contact with uncured materials.
Wrap and where to order
If you follow controlled thinning, slow fills, staged curing and gentle demold, the Size Tulips heart-shaped mold will give consistent embossed tulip accents for full-service manicure and pedicure stations. We keep one mold per station for demand and one spare for backups; at $3.99 each prices may change. For the exact product used on our station order here: https://dynamicnailsupply.com/products/mixed-size-tulips-3d-nail-art-silicone-charm-molds-for-customized-embossed-charms-diy-nail-tools
We hope these steps cut rework and keep charm quality steady—let’s make every pedicure add-on count.